Revereware Revival: Tarnish Removal Tips

Tarnished RevereWare pots and pans can be a challenge to clean, but with the right techniques, it is possible to restore them to their original shine. Firstly, it is crucial to let the cookware cool down completely before attempting any cleaning. Once cooled, rinse the pots and pans with hot water to remove any loose debris. For tough stains on the inside, a small amount of a gentle scouring powder like Bar Keeper's Friend can be added, followed by scrubbing with a non-abrasive sponge. For burnt-on food, fill the cookware with hot water and add a few drops of dish soap, bringing it to a boil and then letting it simmer for about 10 minutes. This will loosen any stubborn food particles. To tackle tough stains on the outside of the cookware, a mixture of vinegar and water can be applied, followed by scrubbing with a sponge. For copper bottoms, a combination of lemon, vinegar, or salt with common table salt can effectively remove tarnish. It is important to avoid using abrasive materials like steel wool and harsh chemicals, as these can damage the surface of the pots and pans. Instead, opt for gentle cleaners like baking soda or vinegar.

Using lemon and salt

Lemon and salt can be used to clean Revere Ware pots and pans and bring copper bottoms back to life. This method is inexpensive, easy, and green.

To clean your Revere Ware with lemon and salt, you will need a lemon or lemon juice, salt, and a soft, clean cloth or paper towels. It is recommended to wear gloves and reading glasses and to put down a sheet to protect against mess. If using a lemon, cut one in half and sprinkle some salt on it. Start off by gently rubbing the lemon following the circular edge of the cookware so that you don't mark the pan. Alternatively, sprinkle salt on the pan, squeeze lemon juice onto the cloth, and gently rub the pan.

Lemon and salt can also be used to remove heat discoloration from Revere Ware. Simply sprinkle salt on the pulp of the lemon and rub lightly over the copper-clad bottom. Every trace of heat discoloration will quickly disappear. Vinegar and salt or sour milk and salt may be used instead of lemon and salt. If the copper does not respond to the lemon and salt treatment, grease may have been burned onto the bottom of the pan. In this case, it will be necessary to first scour the burned portions with an abrasive cleanser, after which the lemon and salt treatment will easily restore the original luster.

Vinegar and salt

Firstly, wet the copper bottom of the pan. You can do this by spraying vinegar onto the copper with a spray bottle, or by using a cloth dampened with vinegar. Next, sprinkle salt onto the vinegar. You can either sprinkle regular salt or use a piece of lemon and sprinkle the salt on the pulp. Then, scrub the pan with a sponge. The chemical reaction between the vinegar and salt will remove the tarnish.

If the copper does not respond to the vinegar and salt treatment, grease may have been burned onto the bottom of the pan. In this case, you will need to first scour the burned portions with an abrasive cleanser, and then the vinegar and salt treatment can be applied to restore the original lustre.

This method can also be used to clean the inside of the pan. Fill the pan with water and add a generous amount of vinegar. Bring the mixture to a boil and let it boil for 15-30 minutes.

Baking soda and water

To use this method, start by sprinkling a generous amount of baking soda onto the affected area of the pot or pan. Then, add water to create a paste. You can adjust the consistency of the paste by adding more or less water. Once the paste is ready, use a damp cloth to rub it into the surface of the cookware. Let the paste sit for a few minutes to allow the baking soda to work its magic. Finally, rinse the cookware thoroughly with water to remove the paste and reveal the clean surface.

For more stubborn tarnish, you can create a stronger paste by using less water. You can also try using a soft-bristled brush or sponge to gently scrub the paste into the cookware, taking care not to scratch the surface. If the tarnish is still not coming off, you can let the paste sit for a few hours to give the baking soda more time to work.

After removing the tarnish, be sure to dry the cookware thoroughly with a clean, dry cloth or by air-drying it. This will prevent water spots from forming and help maintain the shine of your Revere Ware.

By following these steps, you can effectively remove tarnish from your old Revere Ware pots and pans using baking soda and water, restoring them to their original shine.

Dish soap and hot water

Firstly, ensure that your Revere Ware has cooled completely before attempting to clean it. Cleaning hot cookware can be dangerous and may cause serious injury. Once it has cooled down, rinse the cookware with hot water to remove any loose debris.

Then, fill the pot or pan with hot water and add a few drops of dish soap. Bring the water to a boil, and then reduce the heat to let it simmer for about 10 minutes. This process will help loosen any burnt-on food or stubborn stains, making them easier to remove.

After simmering, allow the cookware to cool down again before scrubbing it gently with a non-abrasive sponge or brush. Avoid using steel wool or any abrasive scrubbers, as they can scratch the surface of your Revere Ware.

If there are still burnt-on food particles or tough stains, you can repeat the process or try using a mixture of baking soda and water. Sprinkle a generous amount of baking soda onto the affected area, add water to create a paste, and then let it sit for a few hours. The baking soda mixture will help break down the burnt-on residue.

Finally, rinse the Revere Ware thoroughly with hot water and dry it completely. You can use a clean, dry cloth to wipe the pots and pans or leave them to air dry.

By following these steps, you can effectively remove tarnish from your old Revere Ware pots and pans using dish soap and hot water. This method is simple yet effective and will help restore the original shine to your cookware.

Commercial cleaner

If your Revere Ware pots and pans are heavily tarnished and discoloured, you may want to use a commercial cleaner.

A good commercial cleaner will be able to remove tough stains and burnt-on food without damaging the surface of your cookware. It is important to follow the instructions carefully and to rinse the pots and pans thoroughly after use.

One recommended product is Bar Keeper's Friend. This is a gentle but effective cleaner that is designed to clean stainless steel without scratching or damaging the surface. To use it, first moisten the pan with water, making sure that any burnt-on food is saturated. Then, sprinkle the cleaner onto the bottom of the pan to form a paste. Use a non-abrasive scrubber or soft cloth to scrub the paste into the scorched food and then rinse the pan with clean water. If burn marks are still visible, the process can be repeated.

For stubborn burn marks and carbon build-up, a more powerful cleaner may be required, such as Carbon Off. Revere Ware also has its own liquid or powder copper cleaners for copper bottom utensils, and a stainless cleaner for carbon core and aluminium bottom utensils, bakeware, and stainless steel tea kettles.

Frequently asked questions