Getting Started With Sevtech: Acquiring Your First Pan

In SevTech, a pan is required to make an ender pearl, which is crafted in a Luminus crafting table. To craft a pan, you need to make a pan cast. To make a pan cast, you need to place a pan on a casting table and pour molten gold or molten aluminium brass over it. You can make a pan by placing a blank pattern in the stencil table and selecting the pan button in the GUI.

Use a pan stencil

To get a pan in Sevtech, you can use a pan stencil to make a stone pan. Here's a step-by-step guide on how to do it:

First, you'll need to create a Stencil Table by placing a Blank Pattern on top of a Wooden Plank. This will allow you to create various stencils for crafting tools and weapons. In this case, you'll be using it to create a pan stencil.

Once you have your Stencil Table, you can start the process of making the stone pan. Place a Blank Pattern in the left slot of the Stencil Table's GUI. Then, click on the Pan Pattern button, and you'll find the pan stencil in the right slot of the GUI.

Now that you have your pan stencil, it's time to make the stone pan. Take the pan stencil and place it on the Part Builder. Add some stone to the Part Builder as well. This will create a stone version of the pan.

With your stone pan ready, you can now use it to make a pan cast. Place the stone pan on a Casting Table and pour gold over it. This will create a gold pan cast, which can then be used for your Ender Pearl.

It's important to note that the ingot or cast will be consumed in the process of making the pan cast. Additionally, make sure to use non-flammable materials for the stone pan, such as cobblestone.

By following these steps and using a pan stencil, you can successfully create a stone pan and a pan cast, which are essential for progressing in the Lightwell quest in Sevtech.

Make a stone pan

To make a stone pan in Sevtech, you will need to craft a pan cast. This can be done by placing a pan on a casting table and pouring 288mB (two ingots) of molten gold or molten aluminium brass over it. The pan used in this process will be consumed in the process, so it should be crafted from non-flammable materials such as cobblestone.

To craft the stone pan itself, you will first need to obtain a blank pattern and place it in a stencil table. In the GUI, select the pan button to create a pan pattern. Then, use a part builder to create a stone version of the pan.

It is worth noting that there are alternative methods to crafting a pan cast. One method involves using a pan stencil and pouring two ingots worth of gold onto the pan to create a pan cast. Another method is to use a wooden pan cast template and pour molten copper or gold over it to create a cast.

Pour gold onto the pan stencil

To get a pan in Sevtech, you will need to progress through the early game and unlock several key items and technologies. Here is a step-by-step guide on how to achieve this:

Now, for the topic of pouring gold onto the pan stencil:

Pouring gold onto the pan stencil is a crucial step in crafting your gold pan in Sevtech. This process will create the distinctive concave shape of the pan, which is essential for its functionality. To start, you must first craft a pan stencil. This is created by placing a regular slab of stone and a gold ingot in your crafting table. Ensure you have the required amount of gold ingots ready, as you will need to pour molten gold onto the stencil. The amount of gold required may vary depending on the recipe, so it is good to have extra on hand. Place the pan stencil on a heat-resistant surface, as you will be pouring molten gold onto it. The game recommends using a stone-crafted anvil or a heat-resistant crafting station. Be very cautious during this step to avoid injuries or accidents.

Once your setup is ready, it's time to melt your gold. You will need a furnace or a crucible to melt the gold ingots into a molten form. Place your gold ingots in the furnace and heat them until they liquefy. Be cautious and avoid overheating, as this can affect the quality of your gold and its liquidity. Once your gold is molten, carefully remove it from the heat source and prepare to pour. Pouring the molten gold onto the stencil requires a steady hand and caution. Hold the crucible or container with the molten gold carefully and pour it slowly and evenly onto the center of the pan stencil. Ensure you are wearing heat-resistant gloves and protective eyewear during this step.

Allow the molten gold to set and cool down completely. This process may take some time, and it is crucial to be patient. The cooling time will vary depending on the amount of gold used and the ambient temperature. Once the gold has cooled and solidified, carefully remove the pan stencil by breaking the slab below it. You should now have a perfectly shaped gold pan, ready for the next steps in the crafting process. Remember that you can always gather more gold and try again if you are unhappy with your first attempt. Crafting a gold pan is an art, and with practice, you will improve and get better results.

Use a wooden pan cast template

To get a pan in Sevtech, you will need to use a wooden pan cast template. This process involves several steps and can be challenging to figure out, as clear instructions are not always readily available. Here is a detailed guide to help you through the process:

First, you will need to obtain Ender Dust, which can be used to make an Ender Pearl in Sevtech. This is a crucial component, as it will be melted down and cast to create your pan.

Next, you will need to create a wooden pan cast template. This template will serve as the basis for your final pan. Place this template in the casting table. At this point, clicking on the nozzle may not yield any results, and that is expected.

Now, you will create a stone pan. To do this, take non-flammable material—cobblestone is a common choice—and place it on the casting table. Then, pour gold over it to create your stone pan. This step consumes the gold and the stone pan, so be prepared to have enough resources for multiple attempts if needed.

With your stone pan ready, you can now use it to create your final pan. Place the stone pan on the casting table and pour molten gold over it. This process will consume the stone pan, so ensure you have enough gold for this step.

By following these steps and using your wooden pan cast template effectively, you will successfully create a pan in Sevtech. This process may take some time and experimentation, but with patience and the right resources, you'll be able to craft the pan you need.

Use a gold pan cast

To use a gold pan cast in Sevtech, you will need to make a pan cast. This can be done by following these steps:

Firstly, you will need to gather the necessary materials. You will need gold, which can be used to make the cast, and a non-flammable material such as cobblestone to make the pan. Once you have these materials, you can begin the crafting process.

Make a pan from the non-flammable material. This pan will be used to create the cast, so it needs to be the appropriate size and shape for your desired cast. Place this pan on a casting table.

Next, melt your gold in a porcelain melter. Once the gold is molten, you can begin the casting process. Pour the molten gold over the pan on the casting table. This will create your gold pan cast.

Be aware that the pan used to make the cast will be consumed in the process, so you may need to make multiple pans if you intend to create multiple casts. Once you have your gold pan cast, you can use it to cast items in any metal of your choice.

It is important to note that the gold pan cast is specifically required for certain items, such as ender pearls. Ender pearls are crafted using ender dust, which is melted and then cast using the gold pan cast. This is part of the Lightwell quest in Stage 2 of Sevtech.

Frequently asked questions