The 2008 CX-9 oil pan drain plug is located under the car, towards the rear. The drain plug has a 15mm head and requires a 15mm socket to remove. The plug should be turned counter-clockwise to open it and drain the oil from the engine.
Characteristics | Values |
---|---|
Socket size | 15mm |
Drain plug size | M12-1.75 Thread, 15 mm Head |
What You'll Learn
The drain plug is 15mm
The drain plug for the 2008 CX-9 is 15mm. This is the tool you need to open the oil drain plug so that the used oil can drain from the engine.
The first step is to warm up the engine, which thins the oil, allowing it to drain smoothly. Then, firmly set the parking brake and place jack stands under the car. The drain plug should still be warm from the heated engine.
The 2008 CX-9's drain plug is located under the car. You will need a 15mm socket in the socket wrench, which should fit over the drain plug's nut. Turn it counterclockwise and the oil drain plug should open easily, draining the used oil from the engine.
Make sure to place a bucket and some newspaper under the car's engine to catch the draining oil.
The drain plug is made of corrosion-resistant materials and is a cost-effective solution, offering original equipment performance at a competitive price. It has also been quality tested, undergoing try-on testing to ensure a quality seal.
Gerst Performance Suspension: Oil Pan and Beyond
You may want to see also
The plug has a thick rubber washer
When it comes to oil pan drain plugs, there are a variety of options available, including copper crush washers, rubber gaskets, and aluminum washers. While some people reuse or anneal copper washers, others opt for the convenience of rubber gaskets or the durability of aluminum washers.
Now, let's talk about the 2008 Mazda CX-9 oil pan specifically. The drain plug for this vehicle is the M12-1.75 Thread, 15 mm Head, 1 Pack (Part No.65430) from Dorman. This replacement drain plug is designed to match the original equipment's fit and function, ensuring a quality seal. It is made of corrosion-resistant materials, offering reliable service and a cost-effective solution.
When it comes to the socket size for the 2008 CX-9 oil pan, the exact size is not specified in the sources. However, based on the drain plug specifications, it is likely that a 15 mm socket would be required to remove and install the drain plug.
Now, let's focus on the thick rubber washer aspect of your query. While the Dorman drain plug mentioned above does not explicitly mention a thick rubber washer, it does emphasize ensuring a quality seal. This suggests that the drain plug may come with a washer or gasket to prevent leaks.
In general, rubber washers or gaskets are used with oil pan drain plugs to create a tight seal and prevent leaks. The rubber material is flexible and can conform to the shape of the drain plug and the oil pan, filling any gaps and preventing oil from escaping.
When installing an oil pan drain plug with a rubber washer, it is important to lubricate the rubber surface with oil before tightening the plug. This helps to create a better seal and prevents the rubber from sticking or tearing during installation.
Additionally, it is crucial to torque the drain plug to the specified value for your vehicle. Over-tightening can damage the rubber washer and lead to leaks, while under-tightening may result in the plug backing out.
In summary, when it comes to the 2008 Mazda CX-9 oil pan, the Dorman M12-1.75 drain plug is a reliable and cost-effective option. While the exact socket size is not specified, a 15 mm socket is likely required. As for the thick rubber washer, the Dorman drain plug is designed for a quality seal, and proper installation techniques, including lubrication and correct torque, are essential for ensuring a leak-free seal.
Erase Burn Stains from Stainless Steel: A Comprehensive Guide
You may want to see also
The plug is located at the bottom of the oil pan
The oil drain plug is located at the bottom or side of the oil pan, which is attached to the bottom of the engine. The plug is usually positioned at the lowest possible point on the oil pan, but it can also be found attached to the side, where it is better protected from damage. This means that locating the plug and accessing it can be two different things, as plugs can be in tight spots that are difficult to reach without the right tools.
For a 2008 CX-9, the oil drain plug has an M14-1.50 thread and a 17mm head. This is a direct replacement for a damaged or worn original drain plug, matching the thread pitch to ensure a quality seal.
Clean Stubborn, Baked-on Food Off Your Pans Easily
You may want to see also
The plug is turned counter-clockwise to be removed
To remove the oil drain plug, you must turn it counter-clockwise. This is the left-loosey direction, and it is important to know this to avoid stripping the threads. The plug is usually located near the front of the engine. Before removing the plug, let the car engine run for 10 minutes to make the process easier. Once the plug is removed, the hot oil will begin to pour out, so ensure that you have a pan to collect it. After the oil has finished draining, wipe the screw and plug opening before reinstalling the plug with a new gasket. Be sure not to over-tighten the plug, as this can make it difficult to remove during the next oil change.
The Mazda CX-9 oil drain plug is available at various automotive retailers and online stores. The standard size for this plug is M14-1.50 Thread with a 17 mm head, but it is recommended to check your vehicle's specific requirements before purchasing.
Hot Pot Heroes: The Vegetable Edition
You may want to see also
The plug is tightened to 25-30 foot-pounds
When it comes to tightening the plug on your 2008 CX-9 oil pan, it's important to get the torque just right. Too much torque can stretch and crack the plug's metal shell, leading to serious engine damage. On the other hand, if the plug is too loose, it may blow out of the spark plug hole, damaging the engine's cylinder head.
The correct torque for spark plugs depends on the type of spark plug and the material of the cylinder head. For example, flat seat type spark plugs with gaskets require different torque specifications than conical seat type spark plugs without gaskets. It's best to consult your car's manual or a repair database to find the correct torque specifications for your vehicle.
In general, spark plugs should be tightened until they are snug, and then given an additional turn or fraction of a turn. This can be done by feel, but if you're unsure, it's best to use a torque wrench. Torque wrenches should be calibrated according to the required torque specifications, and some wrenches are better suited for certain ranges than others. For example, a 3/8-inch drive torque wrench is typically used for spark plugs and is calibrated in inch-pounds.
When tightening the plug on your 2008 CX-9 oil pan, make sure to use the correct torque specifications and the appropriate tools to avoid damaging your engine.
Removing Black Soot from Non-Stick Pans: Quick Solutions
You may want to see also
Frequently asked questions
You will need a 15mm socket to change the oil in a 2008 CX-9.
If the drain plug is stuck, try soaking it in WD40 or liquid wrench. You may also need a longer handle or a breaker bar.
Yes, the crush washer should be replaced.